Hamdy Abo Ali Hassan Ibrahim

Faculty of Engineering

Assiut University

Department
Power Mechanical Engineering Department
Fax No
N/A
Email:
hamdyaboali@yahoo.com
MIS Email
hamdyaboali@aun.edu.eg
Mobile
01028688228
Office
N/A - 1681
Google Scholar
google_scholar

Ph. D. In () , , 2009

Professor  Faculty of Engineering, Assiut University , 2021
Associate Professor Faculty of Engineering, ِِAssiut University , 2016

Lecturer Faculty of Engineering, ِِAssiut University , 2011

Assistant Lecturer Faculty of Engineering, Assiut University , 2002

Demonstrator Faculty of Engineering, Assiut University , 1995

# Title Research Year
1 Techno-enviro-economic analysis of hydrogen production via low and high temperature electrolyzers powered by PV/Wind turbines/Waste heat 2023
2 Experimental evaluation of the performance of newly designed tubular SAH with infinity (∞) shaped inner tubes 2023
3 Energy and exergy evaluation of new design nabla shaped tubular solar air heater (∇ TSAH): Experimental investigation 2023
4 Experimental assessment of novel designed solar hot water storage collector incorporating an array of partitioned ducts absorber 2023
5 Utilization of triply periodic minimal surfaces for performance enhancement of adsorption cooling systems: Computational fluid dynamics analysis 2023
6 Performance evaluation of direct and indirect thermal regulation of low concentrated (via compound parabolic collector) solar panel using phase change material-flat heat pipe cooling system 2023
7 Numerical investigation of the air conditioning system performance assisted with energy storage of capsulated concave/convex phase change material 2023
8 Assessment of standalone streetlighting energy storage systems based on hydrogen of hybrid PV/electrolyzer/fuel cell/ desalination and PV/batteries 2023
9 Energy audit, techno-economic, and environmental assessment of integrating solar technologies for energy management in a university residential building: A case study 2023
10 Energy management of standalone cascaded adsorption-compression refrigeration system using hybrid biomass-solar-wind energies 2022
11 Energy, exergy, and economic assessment of thermal regulation of PV panel using hybrid heat pipe-phase change material cooling system 2022
12 Experimental investigation on the performance of parallel and staggered arrays of PCM energy storage system for PV thermal regulation 2022
13 Performance evaluation of PV panels/wind turbines hybrid system for green hydrogen generation and storage: Energy, exergy, economic, and enviroeconomic 2022
14 Performance investigation of hybrid adsorption-compression refrigeration system accompanied with phase change materials Intermittent characteristics 2022
15 Renewable energy-based cascade adsorption-compression refrigeration system: Energy, exergy, exergoeconomic and enviroeconomic perspectives 2022
16 Boosting the air conditioning unit performance using phase change material: Impact of system configuration 2022
17 Energy, exergy, and economic analysis of tubular solar air heater with porous material: An experimental study 2021
18 Enhancement of the daily performance of solar still by exhaust gases under hot and cold climate conditions 2021
19 Energy and exergy assessment of new designed solar air heater of V-shaped transverse finned absorber at single-and double-pass flow conditions 2021
20 Assessment of double-pass pin finned solar air heater at different air mass ratios via energy, exergy, economic, and environmental (4E) approaches 2021
21 Energy, exergy, economic and environmental assessment of double pass V-corrugated-perforated finned solar air heater at different air mass ratios‏ 2021
22 An assessment of energy, exergy and CO2 emissions of a solar desalination system under hot climate conditions 2021
23 Investigation of a solar still behaviour using response surface methodology 2021
24 Productivity, exergy, exergoeconomic, and enviroeconomic assessment of hybrid solar distiller using direct salty water heating 2021
25 Impact of energy storage of new hybrid system of phase change materials combined with air-conditioner on its heating and cooling performance 2021
26 Energy audit and management of an industrial site based on energy efficiency, economic, and environmental analysis 2020
27 Impact of condenser heat transfer on energy and exergy performance of active single slope solar still under hot climate conditions 2020
28 Fractional modeling for enhancing the thermal performance of conventional solar still using hybrid nanofluid: Energy and exergy analysis 2020
29 Impact a combination of geothermal and solar energy systems on building ventilation, heating and output power: Experimental study 2020
30 Enhancement of hybrid solar desalination system composed of solar panel and solar still by using porous material and saline water preheating 2020
31 An experimental investigation of the performance of new design of solar air heater (tubular) 2020
32 An experimental work onlthelperformance oflsolar cell cooled bylfat  heat pipe 2020
33 Energy payback time, exergoeconomic and enviroeconomic analyses of using thermal energy storage system with a solar desalination system: An experimental study 2020
34 Enhancement of waste heat recovery from vertical chimney via thermoelectric generators by heat spreader 2020
35 Enhancement the combustion aspects of a CI engine working with Jatropha biodiesel/decanol/propanol ternary combinations 2020
36 Energy and exergy assessment of integrating reflectors on thermal energy storage of evacuated tube solar collector-heat pipe system 2020
37 Optimal Scheduling of Hybrid Multi-Carrier System Feeding Electrical/Thermal Load Based on Particle Swarm Algorithm 2020
38 3D study of convection-radiation heat transfer of electronic chip inside enclosure cooled by heat sink 2020
39 Energy, exergy, and enviroeconomic assessment of double and single pass solar air heaters having a new design absorber 2020
40 An experimental work on the impact of new combinations of solar chimney, photovoltaic and geothermal air tube on building cooling and ventilation 2020
41 Energy, exergy, economic and environmental assessment of using different passive condenser designs ofsolardistiller 2020
42 Investigation experimentally the impact of condensation rate on solar still performance at different thermal energy storages 2020
43 Study of the performance of double pass solar air heater of a new designed absorber: An experimental work 2020
44 3D study of the impact of aspect ratio and tilt angle on the thermoelectric generator power for waste heat recovery from a chimney 2019
45 Integrative passive and active cooling system using PCM and nanofluid for thermal regulation of concentrated photovoltaic solar cells 2019
46 Experimental work on the effect of saline water medium on the performance of solar still with tracked parabolic trough collector (TPTC)
 		2019
47 Optimal planning of multi-carrier energy hub system using particle swarm optimization 2019
48 Optimized energy management strategy for grid connected double storage (pumped storage-battery) system powered by renewable energy resources 2019
49 An experimental work on the performance of single slope solar still incorporated with latent heat storage system in hot climate conditions
 		2019
50 Optimization for Design of Micro Energy Grids Using Multi-Objective PSO 2019
51 Energy, exergy, economic and enviroeconomic (4E) analyses of solar distillation system using different absorbing materials
 		2019
52 A study on the thermal energy storage of different phase change materials incorporated with the condenser of air-conditioning unit and their effect on the unit performance
 		2019
53 Effects of graphene nanoplatelet addition to jatropha Biodiesel–Diesel mixture on the performance and emission characteristics of a diesel engine
 		2018
54 Optimal grid connected hybrid energy system for Egyptian residential area
 		2018
55 A 3d model of the effect of using heat spreader on the performance of photovoltaic panel (PV) 2018
56 A numerical study on the effect of the heat sink as condenser on the performance of passive solar still 2018
57 Optimal design of a grid-connected desalination plant powered by renewable energy resources using a hybrid PSO–GWO approach 2018
58 An experimental work on the effect of using new technique of thermal energy storage of phase change material on the performance of air conditioning unit
 		2018
59 Performance, combustion, and emission characteristics of a diesel engine fueled with Jatropha methyl ester and graphene oxide additives
 		2018
60 Energy and exergy analysis of single slope passive solar still under Egyptian climate conditions
 		2017
61 Effect of the condenser type and the medium of the saline water on the performance of the solar still in hot climate conditions 2017
62 Experimental study on the performance of double pass and two inlet ports solar air heater (SAH) at different configurations of the absorber plate 2017
63 Long-term Thermal Energy Storage Using Thermochemical Materials 2017
64 Optimal Sizing of Micro Energy grid Based on Multi-objective Particle Swarm Algorithm 2017
65 Multi-Objective Genetic Algorithm Optimal Planning and Scheduling of Hybrid Energy System Connected to the Egyptian Grid
 		2017
66 Effect of rotation speed on the temperature of starter alternator machine 2016
67 An Experimental and Numerical Study on the Effects of the Flat Heat Pipe Wick Structure on Its Thermal Performance 2015
68 Effect of using nanofluids on the performance of rotating heat pipe 2015
69 Study of the parameters and characteristics of flat heat pipe with nanofluids subjected to periodic heat load on its performance 2015
70 Natural convection of Cu-water nanofluid in an enclosure with heat sink and discrete heat source 2014
71 Effet de l’excentricité sur le transfert de chaleur et l’épaisseur du film liquide dans un caloduc tournant 2014
72 effect rotation speed on the cooling of starter alternator machine 2014
73 Effect of eccentricity on the heat transfer and liquid film thickness of revolving heat pipe 2014
74 An experimental work on the effect of injection molding parameters on the cavity pressure and product weight 2013
75 A Three dimensional study on the cooling of electronic component using a flat heat pipe 2013
76 Parametric study on the effect of vapour chamber characteristics on its performance 2013
77 Optimization of region thicknesses of flat heat pipe 2013
78 effect of Cu-water nanofluid on the heat transfer of rotating heat pip 2013
79 3D transient model of vapour chamber: effect of nanofluids on its performance 2013
80 A proposed technique to improve the filling of the mold cavity by polymer during injection molding 2011
81 Transient cooling of electronic components by flat heat pipes 2011
82 A study on the cooling of electronic component by a flat heat pipe 2010
83 modeling the effect of cooling system on the shrinkage and temperature of the polymer by injection molding 2010
84 3D study of cooling system effect on the heat transfer during polymer injection molding 2010
85 Plastic cooling during injection molding ( BOOK ) 2010
86 Heat Transfer during injection molding (BOOK) 2010
87 3D study on the effect of process parameters on the cooling of polymer by injection molding
2009
88 Effect of Filling Stage on the Cooling System Design of Injection Molding 2009
89 Effect of cooling system on the polymer temperature and solidification during injection molding 2009
90 study of optimization of heat transfer in injection molding, analysis their effect on the final properties 2009
91 L’effet de la position des canaux de refroidissement dans le procédé de moulage par injection de polymère thermoplastique, Etude numérique 2009
92 Effect of cooling channels position on the shrinkage of plastic material during injection molding 2009
93 L’effet de la position du seuil d’injection sur le refroidissement d’un polymère dans un moule d’injection 2009
94 Etude et Optimization des Transferts de Chaleur en Injection-Moulage, Analyse de Leur Influence sur les Propriétés Finales 2009
95 A 3D study on the effect of gate location on the cooling of polymer by injection molding 2009
96 Effect of viscous dissipation on the temperature of the polymer during injection molding filling 2008
97 Effect of viscous dissipation on the polymer temperature during injection molding 2008
98 Effect of cooling system on the temperature distribution and solidification degree of polymer by injection molding 2007
99 Effect of the cooling channels position on the solidification degree of the polymer during injection moulding 2007
100 Effect of the position and form of cooling channels on the temperature distribution of polymer during injection moulding 2007
101 Three Dimensional Transient Cooling of electronic Component in an Enclosure Enhanced by Heat Sink: Part II: Parametric Study 2004
102 Three Dimensional Transient Cooling of electronic Component in an Enclosure Enhanced by Heat Sink: Part I: Comparison of experimental and Numerical Results” 2002

الجمعيات العلمية و النقابات :

Research Projects